Si deseas soporte pagado por la configuracion de Unicall u OpenR2 contactame a moises.silva en el correo de google.

y cuando trato de sacar llamada me sale:
voip*CLI>
— Executing [95101652@L-DDN-DDI-CEL:1] Dial(”SIP/100-c0001240″, “Unicall/g1/5101652″) in new stack
MFC/R2 UniCall/1 Call control(1)
MFC/R2 UniCall/1 Make call
MFC/R2 UniCall/1 Creating a new call with CRN 32769
MFC/R2 UniCall/1 0001 -> [1/DIALING /Seize /Idle ]
— Called g1/5101652
[Mar 5 13:10:31] NOTICE[5371]: chan_unicall.c:2518 handle_uc_event: Unicall/1 event Dialing
[Mar 5 13:10:31] NOTICE[5371]: chan_unicall.c:1914 unicall_exception: Exception on 25, channel 1
MFC/R2 UniCall/1 [2/DIALING /Group I /DNIS ]
MFC/R2 UniCall/1 [2/DIALING /Group I /DNIS ]
MFC/R2 UniCall/1 [2/DIALING /Group I /DNIS ]
MFC/R2 UniCall/1 [2/DIALING /Group I /DNIS ]
MFC/R2 UniCall/1 [2/DIALING /Group I /DNIS ]
MFC/R2 UniCall/1 [2/DIALING /Group I /DNIS ]
MFC/R2 UniCall/1 [1/IDLE /Idle /Idle ]
[Mar 5 13:10:31] NOTICE[5371]: chan_unicall.c:2518 handle_uc_event: Unicall/1 event Protocol failure
[Mar 5 13:10:31] ERROR[5371]: chan_unicall.c:2522 handle_uc_event: Unicall/1 protocol error. Cause 32772
MFC/R2 UniCall/1 Channel echo cancel
MFC/R2 UniCall/1 Channel gains
MFC/R2 UniCall/1 Channel switching
— Hungup ‘UniCall/1-1′
== Everyone is busy/congested at this time (1:0/0/1)
— Executing [95101652@L-DDN-DDI-CEL:2] Hangup(”SIP/100-c0001240″, “”) in new stack
== Spawn extension (L-DDN-DDI-CEL, 95101652, 2) exited non-zero on ‘SIP/100-c0001240′
MFC/R2 UniCall/1 [1/IDLE /Idle /Idle ]
voip*CLI>

que sera?

Mi configuracion

zaptel.conf

# Span 1: WCT1/0 “Wildcard TE122 Card 0″ (MASTER)
span=1,1,0,cas,hdb3
# termtype: te
cas=1-15:1101
#dchan=16
cas=17-31:1101
# Span 2: WCTDM/0 “Wildcard AEX410 Board 1″
fxsks=32
fxsks=33
fxsks=34
fxsks=35
# Global data
loadzone = us
defaultzone = us

unicall.conf

[channels]
language=es
usecallerid=yes
hidecallerid=no
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
echotraining=yes
rxgain=0.0
txgain=0.0
group=1
callgroup=1
pickupgroup=1
immediate=no
musiconhold=default
protocolclass=mfcr2
; protocolvariant=co-land,30,1,16
protocolvariant=co-land,30,7,16
protocolend=cpe
group = 1
loglevel = 255
context= from-pstn
channel => 1-15
channel => 17-31
;skip time slot 16

extensions.conf

[from-pstn]
exten=>_.,1,Answer()
exten=>_.,n,Goto(ivr,s,1)
exten=>_.,n,Hangup

exten=>9260,1,Answer()
exten=>9260,n,Goto(ivr,s,1)
exten=>9260,n,Hangup

Tengo entendido q en el zapata.conf no se coloca nada del E1 pero aca les mando:

[trunkgroups]
[channels]
language=es
usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
canpark=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
relaxdtmf=yes
rxgain=0.0
txgain=0.0
callgroup=1
pickupgroup=1
immediate=no
faxdetect=incoming
busydetect=yes
busycount=4

; Span 1: WCT1/0 “Wildcard TE122 Card 0″ (MASTER)
;group=1
;context=from-pstn
;switchtype = euroisdn
;signalling = pri_cpe
;channel => 1-31
; Span 2: WCTDM/0 “Wildcard AEX410 Board 1″
;;; line=”32 WCTDM/0/0 RED”
signalling=fxs_ks
callerid=asreceived
group=2
context=from-pstn
channel => 32
;;; line=”33 WCTDM/0/1 RED”
signalling=fxs_ks
callerid=asreceived
group=2
context=from-pstn
channel => 33
;;; line=”34 WCTDM/0/2 RED”
signalling=fxs_ks
callerid=asreceived
group=2
context=from-pstn
channel => 34
;;; line=”35 WCTDM/0/3 RED”
signalling=fxs_ks
callerid=asreceived
group=2
context=from-pstn
channel => 35

CLI> load chan_unicall.so

Asterisk 1.4

CLI> module load chan_unicall.so

Can you help me in this case ?
How can i load chan_unicall.so module ?
according to above post …. maybe you install MFC/R2 successful.

thanks amjt !

Thanks for reply.
But how can i load chan_unicall.so module ?
(What is command or edit any files?)

Regards!

I eventually will post a guide in the blog, but cannot give you a date for that.

I had install driver for my E1 Card … OK !
I tried to install astunicall 1.4.9-0.1 packages. But I can’t success (I tried install follow guide at http://www.soft-switch.org/unicall/installing-mfcr2.html).
I don’t know why , I don’t see anything such as : UC show channels,status,… in ‘Asterisk CLI>’ … Can you give me the reason about this ?
Can you show me how to install unicall for MFC/R2 step by step…:) if you can.

Thanks a lot !

BestRegards

[Oct 24 09:47:47] NOTICE[2608]: chan_unicall.c:2589 handle_uc_event: Unicall/1 event Proceeding
[Oct 24 09:47:47] NOTICE[2608]: chan_unicall.c:2589 handle_uc_event: Unicall/1 event Far end disconnected
[Oct 24 09:47:47] NOTICE[2608]: chan_unicall.c:2874 handle_uc_event: CRN 32771 – far disconnected cause=Switching equipment congestion [42]
— Channel 0 got hangup
— UniCall/1-1 is circuit-busy
— Hungup ‘UniCall/1-1′
[Oct 24 09:47:47] NOTICE[2608]: cdr.c:434 ast_cdr_free: CDR on channel ‘UniCall/1-1′ not posted
== Everyone is busy/congested at this time (1:0/1/0)
— Executing [s@macro-trunkdial:2] Goto(”SIP/6000-08672190″, “s-CONGESTION|1″) in new stack
— Goto (macro-trunkdial,s-CONGESTION,1)
— Executing [s-CONGESTION@macro-trunkdial:1] NoOp(”SIP/6000-08672190″, “”) in new stack
== Auto fallthrough, channel ‘SIP/6000-08672190′ status is ‘CONGESTION’
[Oct 24 09:47:47] NOTICE[2214]: chan_unicall.c:2589 handle_uc_event: Unicall/1 event Drop call
[Oct 24 09:47:47] NOTICE[2214]: chan_unicall.c:2589 handle_uc_event: Unicall/1 event Release call
— Unicall/1 released

someone knows this problem??
Forgiveness for my English

If you still have this problem contact me and give me ssh access to the buggy box to troubleshoot and see what we can do.